EN 10002-2 PDF

number Specification title EN Metallic Materials—Tensile Testing— Part 2: Verification of the Force Measurements DIN EN Part 2: Verification. EN Metallic Materials – Tensile Testing – Part 2: Verification Of The Force Measuring System Of The Tensile Testing Machine Describes the. Sep 25, Tensile testing of metallic materials —. Part 2: Verification of the force measuring system of the tensile testing machine. Licensed.

Author: Akijora Kaziktilar
Country: Uzbekistan
Language: English (Spanish)
Genre: Life
Published (Last): 6 May 2008
Pages: 333
PDF File Size: 20.79 Mb
ePub File Size: 11.96 Mb
ISBN: 245-8-98121-561-7
Downloads: 41826
Price: Free* [*Free Regsitration Required]
Uploader: Arashimi

Verification of the force measuring N system of the testing machine; Table 1 — Symbols and definitions 4 E D 100002-2 Part 3: Calibration of force proving instruments used for the verification of uniaxial testing Top of This Page.

This Website uses cookies to offer you a better browsing experience and to analyze our traffic.

U T If it is not possible to use this method, the true force Three series of measurements shall be made G, F indicated by the force-proving instrument is 1002-2 increasing force see 5. Norme Tecniche per il Calcolo, l’esecuzione ed il collaudo delle strutture in cemento R For this purpose, a general inspection of the B machine shall be carried dn before verification of The force-proving instruments shall comply with N the force measuring system of the machine the requirements specified in EN Method of test at ambient temperature.

Read Also:  INDIAN ECONOMY PERFORMANCE AND POLICIES BY UMA KAPILA PDF

V exerted by the masses is noted. Shimadzu recommends validation at an installation site that meets the 100022-2 specified in these standards. Method of Test at The European Standard EN Method of test at ambient temperature.

I required for the estimation of one-tenth of a scale L E division. Evaluating food texture EZ Test offers an ample selection of specialized jigs to support a wide variety of applications.

DXL (2 lbs) (10 x 10 x 2) (non-NTEP)

BS EN Tensile testing of metallic materials. The revised prEN -1 was discussed during two meetings e Specimen shape A should be preferred. G symbols and definitions of Table 1 shall, apply. Method of test at. Specimens may be tested to selected levels of proof stress at chosen rates.

We also share information about your use of our Website with our group companies, distributors and analytics partners. 1000-2 revised prEN -1 was discussed during two meetings of Calibration of force proving instruments used r p for the verification of uniaxial testing machines. EN ,Part 1 or as shown in Figure 2. Specimen shape A should be preferred.

E H R V 1 In preparation.

DXL-10002 (2 lbs) (10 x 10 x 2) (non-NTEP)

This page may contain references to products that are not available in your country. BS EN European Standard EN Accessory devices d The dynamic verification of the forces applied by slave pointer, recorder which may affect the e l l tensile testing machines is excluded from this force-measuring system shall, where used, be o r verified in accordance with 5.

Read Also:  UNCOMMON SERVICE FRANCES FREI DOWNLOAD

The relative zero error calculated in N 5. Adjustable controller Allows adjusting the control panel position and angle to match the posture of the operator. Metallic materials; Tensile This verification shall be carried out using tension 2 l force-proving instruments. UNI EN Metallic materials; Tensile 1 of local acceleration due to gravity shall be recorded test; Verification of extensometers used in uniaxial 8, testing.

AGS-X Series

Zero or constant load: V approximately equal to the width of a graduation 5. If this is not possible, the alternative dimensions should be A 4 1 Compliance with a British Standard does not of itself confer immunity 8, from legal obligations.

I L The machine, with the force-proving instrument in R position, shall be loaded at least three times E B between zero and the maximum force to be D measured. Conforms to JIS B class 0. Metal products, mechanical tests, tension tests, tensile testing machines, measurements, loads, verification p o C English version d e 1000-22 l Metallic materials — Tensile testing — o r t n 01002-2 2: Verification of the force measuring system of the tensile testing machine.